Archivovaná správa #2192 diskusnej skupiny os2-wireless

Archivovaná správa #2192 diskusnej skupiny os2-wireless_users@2rosenthals.com

Od:	"Chris Clayton" <os2-wireless_users@2rosenthals.com>	Celá hlavi?ka Nedekódovaná správa
Odosielate?:	os2-wireless_users-owner <os2-wireless_users-owner@2rosenthals.com>
Hlavi?ka:	[OS2Wireless] anyone have GenMac and NETBIOS/TCPIP working?
Dátum:	Wed, 30 Nov 2005 18:37:47 -0700 (MST)
Komu:	"os2-wireless_users@2rosenthals.com" <os2-wireless_users@2rosenthals.com>

After seeing numerous responses to this issue I think it is time to step and look at what is key to having NETBIOS over TCP/IP operational. 1) NetBIOS over TCP/IP must be properly installed. Unfortunately this is best done using a fresh install oe migration, as 'Selective Install for Networking' sometimes leaves out key files. Though I believe eCS 1.2 is better at this than eCS 1.1 and earlier. 2) The MPTD MPTS setup should look like: a) simplified view for TCP/IP and NetBIOS over TCP/IP or NetBIOS only: Adapter0 - 0 - TCP/IP - 0 - NetBIOS over TCP/IP Adapter1 - 1 - TCP/IP <=== the numbering is key, it must be consistent! - 1 - NetBIOS over TCP/IP Adapter2 - 2 - TCP/IP - 2 - NetBIOS over TCP/IP b) It is more complicated when someone (unnecessarily) chooses to use both NetBIOS and NetBIOS over TCP/IP: Adapter0 - 0 - TCP/IP - 0 - NetBIOS over TCP/IP -1 - NetBIOS Adapter1 - 1 - TCP/IP - 2 - NetBIOS over TCP/IP - 3 - NetBIOS In fact, I would not recommend anyone trying to use both NetBIOS and NetBIOS over TCP/IP with more that one adapter. 3) After exiting MPTS, ibmcom\protocol.ini needs to contain the following (for 3 adapters using NetBIOS over TCP/IP); [NETBIOS] DriverName = netbios$ ADAPTER0 = tcpbeui$,0 ADAPTER1 = tcpbeui$,1 ADAPTER1 = tcpbeui$,2 [tcpbeui_nif] DriverName = tcpbeui$ Bindings = adapter0,adapter1,adpater2 ... 4) MPTS, does not automatically configure ibmlan\ibmlan.ini, but in eCS "System Setup | Network | Select Interfaces for Sharing' should. The resulting ibmlan.ini should look like (again for NetBIOS over TCP/IP with 3 adapters): [networks] net1 = TCPBEUI$,0,LM10,34,100,14 net2 = TCPBEUI$,1,LM10,34,100,14 net3 = TCPBEUI$,2,LM10,34,100,14 [requester] ... wrkservices = peer[,messenger] (messenger is really not needed in a soho use) wrknets = NET1,NET2,NET3 COMPUTERNAME = name DOMAIN = domain [peer] .... srvnets = NET1,NET2,NET3 5) mptn\bin\setup should look something like this for fixed ip addresses: route -fh arp -f ifconfig lo 127.0.0.1 ifconfig lan0 192.168.2.55 netmask 255.255.255.0 metric 0 mtu 1500 ifconfig lan1 192.168.1.55 netmask 255.255.255.0 metric 0 mtu 1500 ifconfig lan2 192.168.0.55 netmask 255.255.255.0 metric 0 mtu 1500 REM ifconfig lan3 REM ifconfig lan4 REM ifconfig lan5 REM ifconfig lan6 REM ifconfig lan7 REM ifconfig sl0 route add default 192.168.2.1 -hopcount 1 ipgate on for dhcp on lan 0 the setup should look like: ifconfig lo 127.0.0.1 dhcpstrt -i lan0 -d 0 ifconfig lan1 192.168.1.55 netmask 255.255.255.0 metric 0 mtu 1500 ifconfig lan2 192.168.0.55 netmask 255.255.255.0 metric 0 mtu 1500 REM ifconfig lan3 REM ifconfig lan4 REM ifconfig lan5 REM ifconfig lan6 REM ifconfig lan7 REM ifconfig sl0 ipgate on The subnet IP address range for lan1 & lan2 could be real (i.e. the subnet actually exists) or 'dummy'. So. once the network is up and running, one should be able shutdown and reconfigure the various lans to appropriate IPs. However, as versatile eCS is when it comes to networking, it is still a client operating system and not meant to be used as a network server or a complex router. However, if one is careful, it will function quite well routing between a DSL connection and a SOHO network using two nic adapters. Three or more adapters??? One really has to take a close look at why this configuration is really needed! Cheers, Chris Clayton On Wed, 30 Nov 2005 15:20:52 -0800, Bob wrote: >** Reply to message from "Frank Vos frankvos@xs4all.nl" on Wed, 30 Nov 2005 >23:09:40 +0100 (CET) > >Here is LANTRAN.LOG. The first part is the boot process and then the last part >is after issuing the "net use" command, which gives the message "The REQUESTER >service could not be started". I do not see any errors although I don't know >why there is reference to token-ring. > > > >LT00073: FFST/2 is installed but is not started. LANTRAN.LOG is being created. >IBM OS/2 LANMSGDD [05/21/04] 6.00 is loaded and operational. >IBM OS/2 NETBEUI 6.00.0 >NETBEUI: Using a 32-bit data segment. >Installing NETWKSTA.200 Version 6.0. IBM LAN Redirector ( May 25, 2005) > >IBM OS/2 NETBIOS 4.0 >Adapter 0 has 123 NCBs, 96 sessions, and 6 names available to NETBIOS >applications. >Adapter 1 has 123 NCBs, 96 sessions, and 6 names available to NETBIOS >applications. >Adapter 2 has 123 NCBs, 96 sessions, and 6 names available to NETBIOS >applications. >NETBIOS 4.0 is loaded and operational. >GENPRISM_NIF: APM registered. >GENPRISM_NIF is loaded and operational. >IBM LANVDD is loaded and operational. >IBM OS/2 LAN Netbind >WRND32$ WRAPPER for bus: 2 slot: 2 Vendor: 0x8086 Device: 0x1043. >WRND32$ load SYS: "W70N51.SYS" length: 2479104 CRC: 0x6bb2 / 0x6bb2. >WRND32$ load INF: "W70N51.INF" length: 2041. >WRND32$ WRAPPER hardware init successfull MAC : 000CF1:28897E. >WRND32$ bound to "VECTOR". >GENPRISM_NIF: OpenAdapter called. > >issued "net use" > >Adapter 0 is using node address 000D608B5786. The Token-Ring format is >00B006D1EA61. >GENPRISM_NIF: SetLookAhead called. Param1=256 >GENPRISM_NIF: AddMulticastAddress called. Param2= 3 0 0 0 0 1 >GENPRISM_NIF: AddMulticastAddress rc=0 >GENPRISM_NIF: SetPacketFilter called. Param1=3 >GENPRISM_NIF: SetPacketFilter rc=0 >Adapter 1 is using node address FFFFFFFFFFFF. The Token-Ring format is >FFFFFFFFFFFF. >Adapter 2 is using node address 000CF128897E. The Token-Ring format is >00308F14917E. > >-- >Robert Blair >=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-= > >To unsubscribe from this list, send a message to >steward@2rosenthals.com with the command >"unsubscribe os2-wireless_users" in the body >(omit the quotes). > >For help with other commands, send a message >to steward@2rosenthals.com with the command >"help" in the body (omit the quotes). > >This list is hosted by Rosenthal & Rosenthal >P.O. Box 281, Deer Park, NY 11729-0281. Non- >electronic communications related to content >contained in these messages should be directed >to the above address. (CAN-SPAM Act of 2003) > >=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-= > > =-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-= To unsubscribe from this list, send a message to steward@2rosenthals.com with the command "unsubscribe os2-wireless_users" in the body (omit the quotes). For help with other commands, send a message to steward@2rosenthals.com with the command "help" in the body (omit the quotes). This list is hosted by Rosenthal & Rosenthal P.O. Box 281, Deer Park, NY 11729-0281. Non- electronic communications related to content contained in these messages should be directed to the above address. (CAN-SPAM Act of 2003) =-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=

Prihlási?: Nap??a?, Súhrn, Index.
Odhlási?
Mail na ListMastera