From: "Peter Verweij" <os2-wireless_users@2rosenthals.com> Sender: os2-wireless_users-owner <os2-wireless_users-owner@2rosenthals.com> Subject: [OS2Wireless] Login problems Date: Thu, 19 May 2005 09:43:35 +0200 (CEST) To: os2-wireless_users@2rosenthals.com

Hi,

I use two nics on my T40 and it works great. Just a few things to remember.
Each nic should be on its own networking address.
I have the wireless on 192.168.1.18 and the wired on 192.168.3.19
(important is not to have both on 192.168.1.x then the requester doesn't
work).
Next in ibmlan.ini both network adapters should be bound, search for net1
and net2. But if you don't get an error during boot from network200a it
should be oke.
Next if change your wirelesscard ip-address it is sometime needed to stop
the requester with:
net stop req /y
After a minute or so you can start up the requester again with
net start req
and then it should start. If you are to fast the requester startup quits
with an error message.
At the moment on a windows pc so I can't give you the exact errormessage.

One strange thing: assume you have a password: "test" but logon with the
password in capital "TEST" you won't get an error message, you are logged
in, but can't see any share from other computers.

Hope this helps,

Peter

> I never could get two NIC's working in my laptops.  So I use one or the
> other and switch it in MPTS and reboot.  I have used TCP/IP, NetBios and
> NetBios over TCP/IP with no problems that way.
> Sam
>
>
> Dave Saville wrote:
>
>>On Wed, 18 May 2005 11:59:39 -0700, Neil Waldhauer wrote:
>>
>>
>>
>>>On Wed, 18 May 2005 18:34:51 +0100 (BST), "Dave Saville"
>>> <dave@deezee.org>
>>>wrote:
>>>
>>>
>>>
>>>>Have been using my ARtem card with no problems on my ECS 1.14 Tpad -
>>>> but today
>>>>I hit one.
>>>>
>>>>If I have connected via lan0 - cable - then I have no problems but if I
>>>> am
>>>>connected via lan1 - wifi - then I cannot login to get drives mounted.
>>>> Does
>>>>that not work over wifi?
>>>>
>>>>
>>>I haven't gotten it to work on my Ambicom (Prism chipset) or on my Cisco
>>> 350.
>>>But others have gotten it to work. You have to get the right protocols
>>> bound to
>>>the card, and I'm a little confused about binding NetBIOS to multiple
>>> adapters.
>>>
>>>I use NetDrive for wireless. I can mount drives all I want.
>>>
>>>
>>
>>I have added netbios and netbios over tcp to the wifi adapter but it
>> still
>>won't login. If I login using the cable and then shut down the cable and
>> fire
>>up the wifi then it is OK and the mounted drives are still accessable.
>> But
>>starting from just wifi active and the requester hangs until it times
>> out.
>>
>>
>>
>
> =-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=
>
> To unsubscribe from this list, send a message to
> steward@2rosenthals.com with the command
> "unsubscribe os2-wireless_users" in the body
> (omit the quotes).
>
> For help with other commands, send a message
> to steward@2rosenthals.com with the command
> "help" in the body (omit the quotes).
>
> This list is hosted by Rosenthal & Rosenthal
> P.O. Box 281, Deer Park, NY 11729-0281. Non-
> electronic communications related to content
> contained in these messages should be directed
> to the above address. (CAN-SPAM Act of 2003)
>
> =-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=
>
>


=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=

To unsubscribe from this list, send a message to
steward@2rosenthals.com with the command
"unsubscribe os2-wireless_users" in the body
(omit the quotes).

For help with other commands, send a message
to steward@2rosenthals.com with the command
"help" in the body (omit the quotes).

This list is hosted by Rosenthal & Rosenthal
P.O. Box 281, Deer Park, NY 11729-0281. Non-
electronic communications related to content
contained in these messages should be directed
to the above address. (CAN-SPAM Act of 2003)

=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=

: , , .