os2-wireless_users@2rosenthals.com Messaggio archiviato #3849

Da:	"R. Geoffrey Newbury" <os2-wireless_users@2rosenthals.com>	Intestazioni complete Messaggio non codificato
Mittente:	os2-wireless_users-owner <os2-wireless_users-owner@2rosenthals.com>
Oggetto:	[OS2Wireless] Linksys WPC-11 v4
Data:	Mon, 24 Jan 05 10:52:52 -0500
A:	"os2-wireless_users@2rosenthals.com" <os2-wireless_users@2rosenthals.com>

Whether or not your card has the correct chipset, your config.sys seems to be missing a line. The WPC card is a cardbus card. Cardbus cards don't need pcmcia socket services. They act just like a normal PCI NIC under OS/2. You need a line like 'device=c:\ibmcom\macs\genprism.os2' at the bottom of your config.sys. Socket services messes up the interface for cardbus cards.. My config.sys has this section (with the operative line marked) CALL=C:\IBMCOM\PROTOCOL\NETBIND.EXE RUN=C:\IBMCOM\LANMSGEX.EXE DEVICE=C:\MPTN\PROTOCOL\SOCKETS.SYS DEVICE=C:\MPTN\PROTOCOL\AFOS2.SYS DEVICE=C:\MPTN\PROTOCOL\AFINET.SYS DEVICE=C:\MPTN\PROTOCOL\IFNDIS.SYS DEVICE=C:\MPTN\PROTOCOL\AFNB.SYS /S:100 /C:150 /N:21 RUN=C:\MPTN\BIN\AFNBINI.EXE RUN=C:\MPTN\BIN\CNTRL.EXE CALL=C:\OS2\CMD.EXE /C C:\MPTN\BIN\MPTSTART.CMD DEVICE=C:\IBMCOM\PROTOCOL\NETBEUI.OS2 DEVICE=C:\IBMCOM\PROTOCOL\NETBIOS.OS2 ********** DEVICE=C:\IBMCOM\MACS\CBENDIS.OS2 ********** RUN=C:\IBMCOM\PROTOCOL\LANDLL.EXE DEVICE=C:\IBMLAN\NETPROG\RDRHELP.200 IFS=C:\IBMLAN\NETPROG\NETWKSTA.200 /I:C:\IBMLAN /N If you leave the pc drivers in, then read the Readme for the /ig (ignore) switch and set it to ignore the correct slot. I run a Xircom cardbus (wired) ethernet card in my Thinkpad 600 laptop using the above config.sys. It needs *only* the cbendis.os2 driver. If the Linksys card is built to cardbus specification, it should need *only* the genprism.os2 driver. Try removing the pcmcia drivers. The power light has nothing to do with the drivers installed. Of course, if you have the wrong chipset, none of this will matter.... Good luck. Geoff On Sat, 22 Jan 2005 05:18:29 -0800 (PST), jayant murthy wrote: >I actually received a Linksys WPC-11 v4 and not v3 but >that ssems to be ok. I was hoping to plug and play but >of course no such luck. > >First I installed the PCMCIA drivers using >cardbus.exe. At least the power light on the card goes >on. Next I installed genprism2.0rc4 but XWLan shows >that no card is present. I append my PCMCIA statements >and the protocol.ini. What should I check for/try? > >Thanks, >Jayant >BASEDEV=PCMCIA.SYS >BASEDEV=IBM2SS14.SYS >BASEDEV=AUTODRV2.SYS >DEVICE=C:\THINKPAD\VPCMCIA.SYS >DEVICE=C:\THINKPAD\PCMSSDIF.SYS >DEVICE=C:\THINKPAD\PCM2SRAM.SYS >DEVICE=C:\THINKPAD\FLSH2MTD.SYS >DEVICE=C:\THINKPAD\PCM2FLSH.SYS >BASEDEV=PCM2ATA.ADD /S:2 /!DM /NOBEEP > >[PROT_MAN] > > DRIVERNAME = PROTMAN$ > >[IBMLXCFG] > > tcpip_nif = tcpip.nif > E1000_nif = E1000.NIF > GENPRISM_nif = genprism.nif > >[tcpip_nif] > > DriverName = TCPIP$ > Bindings = E1000_nif,GENPRISM_nif > >[E1000_nif] > > DriverName = E1000$ > >[GENPRISM_nif] > > DriverName = PRISMC$ > HW_TYPE = "PCCARD" > DESIRED_SSID = "IBM" > STA_MODE = "BSS" > CREATE_IBSS = "NO" > PREAMBLE = "BOTH" > MW_ROBUSTNESS = "NO" > PSP_MODE = "DISABLED" > WEP = "DISABLED" > AUTH_TYPE = "OPEN_SYSTEM" > SUPPLY_VOLTAGE = "3.3V" > DEBUG_LEVEL = 0xFF1F > > >===== >************************************************************************* >Jayant Murthy (Professor) >Indian Institute of Astrophysics, Koramangala, Bangalore - 34, India >(91) (80) 25530672 (Operator) 25539250/51 Ext 263 (Direct dial) >(91) (80) 25534043 (FAX) jmurthy@yahoo.com >http://www.iiap.res.in/personnel/murthy/index.htm >TAUVEX web page: http://www.iiap.res.in/tauvex/tauvex.html >************************************************************************** > > > >__________________________________ >Do you Yahoo!? >All your favorites on one personal page û Try My Yahoo! >http://my.yahoo.com >=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-= > >To unsubscribe from this list, send a message to >steward@2rosenthals.com with the command >"unsubscribe os2-wireless_users" in the body >(omit the quotes). > >For help with other commands, send a message >to steward@2rosenthals.com with the command >"help" in the body (omit the quotes). > >This list is hosted by Rosenthal & Rosenthal >P.O. Box 281, Deer Park, NY 11729-0281. Non- >electronic communications related to content >contained in these messages should be directed >to the above address. (CAN-SPAM Act of 2003) > >=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-= > R. Geoffrey Newbury newbury@mandamus.org Barrister and Solicitor Telephone: 905-271-9600 Mississauga,Ontario, Canada Facsimile: 905-271-1638 =-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-= To unsubscribe from this list, send a message to steward@2rosenthals.com with the command "unsubscribe os2-wireless_users" in the body (omit the quotes). For help with other commands, send a message to steward@2rosenthals.com with the command "help" in the body (omit the quotes). This list is hosted by Rosenthal & Rosenthal P.O. Box 281, Deer Park, NY 11729-0281. Non- electronic communications related to content contained in these messages should be directed to the above address. (CAN-SPAM Act of 2003) =-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=

Isriviti: Feed, Riassunto, Indice.
Disiscriviti
Scrivi a ListMaster