Poštni seznam arhiviranih sporo?il

Od:	"Carl Gehr" <os2-wireless_users@2rosenthals.com>	Glava Izvorno E-sporo?ilo
Pošiljalec:	os2-wireless_users-owner <os2-wireless_users-owner@2rosenthals.com>
Zadeva:	[OS2Wireless] IBM High Rate Wireless LAN -128]
Datum:	Sat, 01 Nov 2003 03:17:47 -0500 (EST)
Za:	"os2-wireless_users@2rosenthals.com" <os2-wireless_users@2rosenthals.com>

Lewis and Frank, I thought I had just copied a set of statements from an earlier post. I have no idea why/what these are really doing. [Most of this is 'black-art' to me, but I understand that the DHCP is needed for the active NIC and that is the reason for the exercise.] Unfortunately, I am now away from the Wireless AP, but I will try to have the change [replace mptstart with dhcpstrt] tested by someone who is there and see what happens. Thanks for the response. Carl On Fri, 31 Oct 2003 22:37:29 -0500, Lewis G Rosenthal wrote: >I tend to agree with Frank's point about calling mptstart.cmd. You >should only have to call dhcpstrt, as you have commented, unless there's >something in the NETBIOS setup which is eluding me (I don't do any of >the peer networking stuff, so I don't use NETBIOS; I'm at a bit of a >loss to test this for you). > >On 10/31/2003 02:38 am, Carl Gehr thus wrote : > >>On Thu, 30 Oct 2003 23:26:13 -0500, Lewis G Rosenthal wrote: >> >> >> >>>Sam, as I recall, you were using static IP for the Wi-Fi connection, >>>correct? In this case, you shouldn't need Neil's script, as that simply >>>swaps the DHCP interface from LAN0 to LAN1. In your case, one or both of >>>your interfaces are set to static IP, so you should be good to go with >>>both interfaces configured (just not with the same address, as that is >>>usually used for fault tolerant configurations). >>> >>> >> >>Lewis, >> >>Since you brought up the Cmd files to switch the DHCP between >>interfaces, I'd like to revisit the subject. I just returned from a >>trip where I had easy access to both a wired and wireless connection. >>All attempts to use commands distributed here a while back to switch >>the interface failed. >> >>Just so we're all starting from the same place, here are the specifics >>of my configuration and the command files: >> >>=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+= >> Configuration Information >>~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ >>LAN-0: Wired DriverName = E100B$ >> TCP/IP >> NetBIOS for OS/2 >> DHCP active. >> >>LAN-1: 802.11b DriverName = PRISMP$ >> TCP/IP >> NetBIOS for OS/2 >> >>=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+= >> The Commands >>~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ >>Switch Wired to Wireless >>======================== >>/* CmdName: ActENet.Cmd */ >>/* Turn the Radio ON >> * This command activates the 802.11b interface >> * >> * The wireless NIC should be inserted in the PC Card slot >> */ >>say "Turn the Wireless Radio ON " >>say "Activating the Wireless Network Card" >>'@ ifconfig lan0 down' >>'@ ifconfig lan0 delete' >>'@ dhcpmon -t' >>'@ route -fh' >>'@ arp -f' >> /* '@ dhcpstrt -i lan1 -d 0' */ >>'@ Call c:\mptn\bin\mptstart.cmd -i lan1 -d 5' >>say "Wireless Networking Enabled" >>return >> >>~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ >>Switch Wireless to Wired >>======================== >>/* CmdName: ActENet.Cmd */ >>/* Turn the radio OFF >> * This command activates the 802.11b interface >> */ >>say "Turn the Wireless Radio OFF" >>say "Activating the Ethernet Network Card" >>'@ ifconfig lan1 down' >>'@ ifconfig lan1 delete' >>'@ dhcpmon -t' >>'@ route -fh' >>'@ arp -f' >> /* '@ dhcpstrt -i lan0 -d 0' */ >>'@ Call c:\mptn\bin\mptstart.cmd -i lan0 -d 5' >>say "Ethernet Networking Enabled" >>return >> >>=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+= >> >>So, what am I doing wrong? >> >>Thanks, >>Carl >> >>=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-= =-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-= To unsubscribe from this list, send a message to steward@2rosenthals.com with the command "unsubscribe os2-wireless_users" in the body (omit the quotes). For help with other commands, send a message to steward@2rosenthals.com with the command "help" in the body (omit the quotes). =-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=

Naro?iti: Poro?ilo (Feed), Izvle?ek (Digest), Indeks.
Odjava
E-pošta za mojstra za sezname