MIME-Version: 1.0
Content-Type: text/plain; charset="us-ascii"
Content-Transfer-Encoding: 7bit
Message-Id: <20031101081638.HCZL18933.smtp02.fuse.net@A30pCG>
Date:  Sat, 01 Nov 2003 03:16:37 -0500 (EST)
Sender: os2-wireless_users-owner <os2-wireless_users-owner@2rosenthals.com>
Reply-To: os2-wireless_users@2rosenthals.com
From:  "Carl Gehr" <os2-wireless_users@2rosenthals.com>
To:  "os2-wireless_users@2rosenthals.com" <os2-wireless_users@2rosenthals.com>
Subject: [OS2Wireless] IBM High Rate Wireless LAN -128]

Lewis and Frank,

I thought I had just copied a set of statements from an earlier post. 
I have no idea why/what these are really doing.  [Most of this is
'black-art' to me, but I understand that the DHCP is needed for the
active NIC and that is the reason for the exercise.]

Unfortunately, I am now away from the Wireless AP, but I will try to
have the change [replace mptstart with dhcpstrt] tested by someone who
is there and see what happens.

Thanks for the response.

Carl

On Fri, 31 Oct 2003 22:37:29 -0500, Lewis G Rosenthal wrote:

>I tend to agree with Frank's point about calling mptstart.cmd. You 
>should only have to call dhcpstrt, as you have commented, unless there's 
>something in the NETBIOS setup which is eluding me (I don't do any of 
>the peer networking stuff, so I don't use NETBIOS; I'm at a bit of a 
>loss to test this for you).
>
>On 10/31/2003 02:38 am, Carl Gehr thus wrote :
>
>>On Thu, 30 Oct 2003 23:26:13 -0500, Lewis G Rosenthal wrote:
>>
>>  
>>
>>>Sam, as I recall, you were using static IP for the Wi-Fi connection, 
>>>correct? In this case, you shouldn't need Neil's script, as that simply 
>>>swaps the DHCP interface from LAN0 to LAN1. In your case, one or both of 
>>>your interfaces are set to static IP, so you should be good to go with 
>>>both interfaces configured (just not with the same address, as that is 
>>>usually used for fault tolerant configurations).
>>>    
>>>
>>
>>Lewis, 
>>
>>Since you brought up the Cmd files to switch the DHCP between
>>interfaces, I'd like to revisit the subject.  I just returned from a
>>trip where I had easy access to both a wired and wireless connection. 
>>All attempts to use commands distributed here a while back to switch
>>the interface failed.
>>
>>Just so we're all starting from the same place, here are the specifics
>>of my configuration and the command files:
>>
>>=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=
>>	Configuration Information
>>~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
>>LAN-0:  Wired     DriverName = E100B$
>>                  TCP/IP
>>                  NetBIOS for OS/2
>>                  DHCP active.
>>
>>LAN-1:  802.11b   DriverName = PRISMP$
>>                  TCP/IP
>>                  NetBIOS for OS/2
>>
>>=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=
>>	The Commands
>>~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
>>Switch Wired to Wireless
>>========================
>>/* CmdName:  ActENet.Cmd                        */
>>/* Turn the Radio ON
>> * This command activates the 802.11b interface
>> *
>> * The wireless NIC should be inserted in the PC Card slot
>> */
>>say "Turn the Wireless Radio ON "
>>say "Activating the Wireless Network Card"
>>'@ ifconfig lan0 down'
>>'@ ifconfig lan0 delete'
>>'@ dhcpmon -t'
>>'@ route -fh'
>>'@ arp -f'
>> /*     '@ dhcpstrt -i lan1 -d 0'                 */
>>'@ Call c:\mptn\bin\mptstart.cmd -i lan1 -d 5'
>>say "Wireless Networking Enabled"
>>return
>>
>>~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
>>Switch Wireless to Wired
>>========================
>>/* CmdName:  ActENet.Cmd                        */
>>/* Turn the radio OFF
>> * This command activates the 802.11b interface
>> */
>>say "Turn the Wireless Radio OFF"
>>say "Activating the Ethernet Network Card"
>>'@ ifconfig lan1 down'
>>'@ ifconfig lan1 delete'
>>'@ dhcpmon -t'
>>'@ route -fh'
>>'@ arp -f'
>> /* '@ dhcpstrt -i lan0 -d 0'                   */
>>'@ Call c:\mptn\bin\mptstart.cmd -i lan0 -d 5'
>>say "Ethernet Networking Enabled"
>>return
>>
>>=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=
>>
>>So, what am I doing wrong?
>>
>>Thanks,
>>Carl
>>
>>=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=

=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=

To unsubscribe from this list, send a message to
steward@2rosenthals.com with the command
"unsubscribe os2-wireless_users" in the body
(omit the quotes).

For help with other commands, send a message
to steward@2rosenthals.com with the command
"help" in the body (omit the quotes).

=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=