os2-wireless_users@2rosenthals.com ?????????????? ????? #5960

???:	"Carl Gehr" <os2-wireless_users@2rosenthals.com>	?? ???? ?????????
???:	"OS/2 Wireless Users Mailing List" <os2-wireless_users@2rosenthals.com>
??:	Re: [OS2Wireless] TP Hibernation
??:	Wed, 20 Jun 2007 13:34:51 -0400 (EDT)
??:	"OS/2 Wireless Users Mailing List" <os2-wireless_users@2rosenthals.com>

On Wed, 20 Jun 2007 10:30:11 -0600, Andy Willis wrote: >Carl Gehr wrote: >> On Wed, 20 Jun 2007 05:36:00 -0400 (EDT), Hakan wrote: >> >>>>> Correct, boot with CD and there are only two options: create partition >>>>> and delete partition. I was not constrained by reading any >>>>> instructions... Sadly, I could not get the network connection to work >>>>> after waking up the computer even if I ran SETUP.CMD or TCPSTART.CMD. >>>>> >>>>> >>>> This is most likely a power management issue, possibly addressed by the >>>> ACPI driver. I would suggest reporting this condition on the appropriate >>>> mailing list. >>>> >>>> Kudos for getting the hibernation to work, however. :-) >>> Thanks but I deserve no credit. The hibernation utility had been >>> mentioned on this list some time ago -- don't have the name of the >>> person handy -- and as I was repartitioning the harddisk anyway, it was >>> easy to lay down this partition as the first one on the disk. >>> >>> As for reporting it, I would think an eCS ticket would be most >>> appropriate -- perhaps this has even been fixed in eCS 2.0?? >>> >>> Now I'd love to be able to run the external monitor separately from the >>> LCD, i.e., split the desktop between them and ideally be able to set >>> the resolution separately. Sadly, I think this is definitely not >>> possible with the SNAP driver... >> >> I don't think it is a 'driver' issue; rather a hardware issue. I think >> there is really only one logical device and the BIOS [switched via >> Fn-F7] determines where the data actually goes. >> >> Carl >I am not sure of the card in the T43 but my T42 I am able to split the >desktop between LCD and monitor but I cannot set the resolution >seperately (e.g. I set base resolution of 1400x1050 and across both >monitors it is 2800x1050). For the laptops only ATI cards will do >this as far as I know and then it is not a "supported" feature (not >that SNAP has support at this point) but works quite well (worked with >ATI mobility radeon 7500 ad 9600 here). >Andy OK, I'm obviously wrong... So, how do you do this 'splitting of the desktop' trick? Carl =-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-= This message is sent to you because you are subscribed to the mailing list <os2-wireless_users@2rosenthals.com>. To unsubscribe, E-mail to: <os2-wireless_users-off@2rosenthals.com> To switch to the DIGEST mode, E-mail to <os2-wireless_users-digest@2rosenthals.com> To switch to the INDEX mode, E-mail to <os2-wireless_users-index@2rosenthals.com> Send administrative queries to <os2-wireless_users-request@2rosenthals.com> To subscribe (new addresses), E-mail to: <os2-wireless_users-on@2rosenthals.com> and reply to the confirmation email. Web archives are publicly available at: http://lists.2rosenthals.com This list is hosted by Rosenthal & Rosenthal, LLC P.O. Box 281, Deer Park, NY 11729-0281. Non- electronic communications related to content contained in these messages should be directed to the above address. (CAN-SPAM Act of 2003) =-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=

???????: ????, ??????, ??????.
?????????
??? ????????