| Od: |
"Carl Gehr" <os2-wireless_users@2rosenthals.com> |
Glava
Izvorno E-sporo?ilo |
| Pošiljalec: |
"OS/2 Wireless Users Mailing List" <os2-wireless_users@2rosenthals.com> |
| Zadeva: |
Re: [OS2Wireless] TP Hibernation |
| Datum: |
Wed, 20 Jun 2007 13:34:51 -0400 (EDT) |
| Za: |
"OS/2 Wireless Users Mailing List" <os2-wireless_users@2rosenthals.com> |
|
|---|
On Wed, 20 Jun 2007 10:30:11 -0600, Andy Willis wrote:
>Carl Gehr wrote:
>> On Wed, 20 Jun 2007 05:36:00 -0400 (EDT), Hakan wrote:
>>
>>>>> Correct, boot with CD and there are only two options: create partition
>>>>> and delete partition. I was not constrained by reading any
>>>>> instructions... Sadly, I could not get the network connection to work
>>>>> after waking up the computer even if I ran SETUP.CMD or TCPSTART.CMD.
>>>>>
>>>>>
>>>> This is most likely a power management issue, possibly addressed by the
>>>> ACPI driver. I would suggest reporting this condition on the appropriate
>>>> mailing list.
>>>>
>>>> Kudos for getting the hibernation to work, however. :-)
>>> Thanks but I deserve no credit. The hibernation utility had been
>>> mentioned on this list some time ago -- don't have the name of the
>>> person handy -- and as I was repartitioning the harddisk anyway, it was
>>> easy to lay down this partition as the first one on the disk.
>>>
>>> As for reporting it, I would think an eCS ticket would be most
>>> appropriate -- perhaps this has even been fixed in eCS 2.0??
>>>
>>> Now I'd love to be able to run the external monitor separately from the
>>> LCD, i.e., split the desktop between them and ideally be able to set
>>> the resolution separately. Sadly, I think this is definitely not
>>> possible with the SNAP driver...
>>
>> I don't think it is a 'driver' issue; rather a hardware issue. I think
>> there is really only one logical device and the BIOS [switched via
>> Fn-F7] determines where the data actually goes.
>>
>> Carl
>I am not sure of the card in the T43 but my T42 I am able to split the
>desktop between LCD and monitor but I cannot set the resolution
>seperately (e.g. I set base resolution of 1400x1050 and across both
>monitors it is 2800x1050). For the laptops only ATI cards will do
>this as far as I know and then it is not a "supported" feature (not
>that SNAP has support at this point) but works quite well (worked with
>ATI mobility radeon 7500 ad 9600 here).
>Andy
OK, I'm obviously wrong...
So, how do you do this 'splitting of the desktop' trick?
Carl
=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=
This message is sent to you because you are subscribed to
the mailing list <os2-wireless_users@2rosenthals.com>.
To unsubscribe, E-mail to: <os2-wireless_users-off@2rosenthals.com>
To switch to the DIGEST mode, E-mail to <os2-wireless_users-digest@2rosenthals.com>
To switch to the INDEX mode, E-mail to <os2-wireless_users-index@2rosenthals.com>
Send administrative queries to <os2-wireless_users-request@2rosenthals.com>
To subscribe (new addresses), E-mail to: <os2-wireless_users-on@2rosenthals.com> and reply to the confirmation email.
Web archives are publicly available at: http://lists.2rosenthals.com
This list is hosted by Rosenthal & Rosenthal, LLC
P.O. Box 281, Deer Park, NY 11729-0281. Non-
electronic communications related to content
contained in these messages should be directed
to the above address. (CAN-SPAM Act of 2003)
=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=
|