List os2-wireless_users@2rosenthals.com Arkiverade meddelande #6318

Från:	"Stuart Updike" <os2-wireless_users@2rosenthals.com>	Meddelandehuvud Oavkodat meddelande
Ämne:	Re: [OS2Wireless] Re: Cannot get DHCP
Datum:	Mon, 12 Oct 2009 17:25:23 -0500
Till:	OS/2 Wireless Users Mailing List <os2-wireless_users@2rosenthals.com>

Lewis G Rosenthal wrote: Hi, Stu... On 10/12/09 02:12 pm, Stuart Updike thus wrote : Hello all, I have just installed eCS 2.0rc7 on my ThinkPad T23. I have no problem using the wired connection to my router, a Netgear MR814V2. However, when I enable the wireless card, I cannot connect. At this point, it is an open system. The DHCP Monitor reports the DHCP client is not running. The XWlan widget is showing full green on connection strength. I tried looking at the sample script, but it is Greek to me. Any ideas? Ensure that the DHCP monitor is indeed looking at the correct interface (usually, lan1 vs lan0). Once you've done that, try getting dhcp to start on the interface from a command line, in case there is any valuable feedback: dhcpmon -t route -fh arp -f dhcpstrt -i lan1 (the default timeout of 60 seconds should give you an indication as to whether or not we're even finding a DHCP server on the other end) Make sure that you are seeing a MAC address for your Wi-Fi card (this should be the case; it's only the newer Intels which have this annoyance, AFAICR). I'm not very familiar with the Netgear MR812V2, so I can't offer up any help as to what you might want to check on that end, sorry. Hi Lewis, The wired connection to the router can get a lease very quickly, but the wireless never gets a lease. I do not know how to query the wireless card for its MAC address, but it is labeled on the bottom of the machine and it does show up in the router's list of connected devices. I ran your suggested CMD file. The response is included below: [E:\TEMP]dhcpmon -t [E:\TEMP]route -fh default 192.168.0.1 done [E:\TEMP]arp -f 192.168.0.1 (192.168.0.1) deleted. 192.168.0.255 (192.168.0.255) deleted. [E:\TEMP]dhcpstrt -i lan1 DHCPSTRT: Waiting for DHCP client.(maximum wait = 60 seconds) DHCPSTRT: DHCP client did not start. ----------------End of output----------------------- I tried pinging the IP addresses of the wireless card (192.168.0.3) and the router (192.168.0.1 ). Results below: PING 192.168.0.3: 56 data bytes 64 bytes from 192.168.0.3: icmp_seq=0. time=0. ms 64 bytes from 192.168.0.3: icmp_seq=1. time=0. ms 64 bytes from 192.168.0.3: icmp_seq=2. time=0. ms 64 bytes from 192.168.0.3: icmp_seq=3. time=0. ms 64 bytes from 192.168.0.3: icmp_seq=4. time=0. ms ----192.168.0.3 PING Statistics---- 5 packets transmitted, 5 packets received, 0% packet loss round-trip (ms) min/avg/max = 0/0/0 ---------------------End------------------------ PING 192.168.0.1: 56 data bytes 64 bytes from 192.168.0.1: icmp_seq=0. time=0. ms 64 bytes from 192.168.0.1: icmp_seq=1. time=0. ms 64 bytes from 192.168.0.1: icmp_seq=2. time=0. ms ----192.168.0.1 PING Statistics---- 3 packets transmitted, 3 packets received, 0% packet loss round-trip (ms) min/avg/max = 0/0/0 --------------------------End------------------------------- Just in case it might help, here's the download from Craig Hart's sniffer: Craig Hart's PCI+AGP bus sniffer, Version 1.04vkA, freeware made in 1996-2005. Loaded Vendor Data : "This is version 671 of this file; 22-01-2008 (D-M-Y)." PCI BIOS Version 2.10 found! Number of PCI Busses : 9 PCI Characteristics : Config Mechanism 1 Searching for PCI Devices using the OEMHLP$ driver Bus 0 (PCI), Device Number 0, Device Function 0 Vendor 8086h Intel Corporation Device 3575h 82830M/MG/MP SDRAM Controller / Host-hub Interface (A6-step) Command 0106h (Memory Access, BusMaster, System Errors) Status 2010h (Has Capabilities List, Received Master Abort, Fast Timing) Revision 04h, Header Type 00h, Bus Latency Timer 00h Self test 00h (Self test not supported) PCI Class Bridge, type PCI to HOST Subsystem ID 021D1014h Unknown Subsystem Vendor 1014h IBM Address 0 is a Memory Address (0-4GiB, Prefetchable) : D0000000h..DFFFFFFFh New Capabilities List Present: Vendor-Dependant Capability AGP Capability, Version 2.0 (AGP 4x and below support) AGP Speed(s) Supported : 1x 2x 4x FW Transfers Supported : Yes 4GiB Address Space Supported : No Sideband Addressing Supported : Yes Maximum Command Queue Length : 32 bytes AGP Speed Selected : 4x FW Transfers Enabled : No 4GiB Address Space Enabled : No AGP Enabled : Yes Sideband Addressing Enabled : No Current Command Queue Length : 1 byte Bus 0 (PCI), Device Number 1, Device Function 0 Vendor 8086h Intel Corporation Device 3576h 82830M/MP CPU to AGP Bridge (A6-step) Command 0107h (I/O Access, Memory Access, BusMaster, System Errors) Status 0020h (Supports 66MHz, Fast Timing) Revision 04h, Header Type 01h, Bus Latency Timer 60h Self test 00h (Self test not supported) PCI Class Bridge, type PCI to PCI PCI Bridge Information: Primary Bus Number 0, Secondary Bus Number 1, Subordinate Bus number 1 Secondary Bus Command 000Ch (ISA mapping, VGA mapping) Secondary Bus Status 22A0h (Supports 66MHz, Supports Back-To-Back Trans., Received Master Abort, Medium Timing) Secondary Bus Latency 40h I/O Port Range Passed to Secondary Bus : None Memory Range Passed to Secondary Bus : C0100000h..C01FFFFFh Prefetchable Memory Range Passed to Secondary Bus : E0000000h..EBFFFFFFh Bus 0 (PCI), Device Number 29, Device Function 0 Vendor 8086h Intel Corporation Device 2482h 82801CA USB Controller #1 (ICH3-S B1 step) Command 0005h (I/O Access, BusMaster) Status 0280h (Supports Back-To-Back Trans., Medium Timing) Revision 02h, Header Type 80h, Bus Latency Timer 00h Self test 00h (Self test not supported) PCI Class Serial, type USB (UHCI) Subsystem ID 02201014h Unknown Subsystem Vendor 1014h IBM Address 0 is not present or not configured! Address 1 is not present or not configured! Address 2 is not present or not configured! Address 3 is not present or not configured! Address 4 is an I/O Port : 1800h..1813h System IRQ 11, INT# A Bus 0 (PCI), Device Number 29, Device Function 1 Vendor 8086h Intel Corporation Device 2484h 82801CA USB Controller #2 (ICH3-S B1 step) Command 0005h (I/O Access, BusMaster) Status 0280h (Supports Back-To-Back Trans., Medium Timing) Revision 02h, Header Type 00h, Bus Latency Timer 00h Self test 00h (Self test not supported) PCI Class Serial, type USB (UHCI) Subsystem ID 02201014h Unknown Subsystem Vendor 1014h IBM Address 0 is not present or not configured! Address 1 is not present or not configured! Address 2 is not present or not configured! Address 3 is not present or not configured! Address 4 is an I/O Port : 1820h..1833h System IRQ 11, INT# B Bus 0 (PCI), Device Number 29, Device Function 2 Vendor 8086h Intel Corporation Device 2487h 82801CA USB Controller #3 (ICH3-S B1 step) Command 0005h (I/O Access, BusMaster) Status 0280h (Supports Back-To-Back Trans., Medium Timing) Revision 02h, Header Type 00h, Bus Latency Timer 00h Self test 00h (Self test not supported) PCI Class Serial, type USB (UHCI) Subsystem ID 02201014h Unknown Subsystem Vendor 1014h IBM Address 0 is not present or not configured! Address 1 is not present or not configured! Address 2 is not present or not configured! Address 3 is not present or not configured! Address 4 is an I/O Port : 1840h..1853h System IRQ 11, INT# C Bus 0 (PCI), Device Number 30, Device Function 0 Vendor 8086h Intel Corporation Device 2448h 82801CAM Hub Interface to PCI Bridge (ICH3-M B1 step) Command 0107h (I/O Access, Memory Access, BusMaster, System Errors) Status 0080h (Supports Back-To-Back Trans., Fast Timing) Revision 42h, Header Type 01h, Bus Latency Timer 00h Self test 00h (Self test not supported) PCI Class Bridge, type PCI to PCI PCI Bridge Information: Primary Bus Number 0, Secondary Bus Number 2, Subordinate Bus number 8 Secondary Bus Command 0004h (ISA mapping) Secondary Bus Status 2280h (Supports Back-To-Back Trans., Received Master Abort, Medium Timing) Secondary Bus Latency 40h I/O Port Range Passed to Secondary Bus : 3000h..7FFFh (16-bit) Memory Range Passed to Secondary Bus : C0200000h..CFFFFFFFh Prefetchable Memory Range Passed to Secondary Bus : EC000000h..F7FFFFFFh Bus 0 (PCI), Device Number 31, Device Function 0 Vendor 8086h Intel Corporation Device 248Ch 82801CAM (ICH3-M) LPC Interface Command 000Fh (I/O Access, Memory Access, BusMaster, Special Cycles) Status 0280h (Supports Back-To-Back Trans., Medium Timing) Revision 02h, Header Type 80h, Bus Latency Timer 00h Self test 00h (Self test not supported) PCI Class Bridge, type PCI to ISA Bus 0 (PCI), Device Number 31, Device Function 1 Vendor 8086h Intel Corporation Device 248Ah 82801CAM (ICH3-M) UltraATA/100 EIDE Controller Command 0007h (I/O Access, Memory Access, BusMaster) Status 0280h (Supports Back-To-Back Trans., Medium Timing) Revision 02h, Header Type 00h, Bus Latency Timer 00h Self test 00h (Self test not supported) PCI Class Storage, type IDE (ATA) PCI EIDE Controller Features : BusMaster EIDE is supported Primary Channel is at I/O Port 01F0h and IRQ 14 Secondary Channel is at I/O Port 0170h and IRQ 15 Subsystem ID 02201014h Unknown Subsystem Vendor 1014h IBM Address 0 is an I/O Port : 01F0h..01F7h Address 1 is an I/O Port : 03F4h Address 2 is an I/O Port : 0170h..0177h Address 3 is an I/O Port : 0374h Address 4 is an I/O Port : 1860h..1867h System IRQ (disabled), INT# A Bus 0 (PCI), Device Number 31, Device Function 3 Vendor 8086h Intel Corporation Device 2483h 82801CA SMBus Controller (ICH3-S B1 step) Command 0001h (I/O Access) Status 0280h (Supports Back-To-Back Trans., Medium Timing) Revision 02h, Header Type 00h, Bus Latency Timer 00h Self test 00h (Self test not supported) PCI Class Serial, type SMBus Controller Subsystem ID 02201014h Unknown Subsystem Vendor 1014h IBM Address 0 is not present or not configured! Address 1 is not present or not configured! Address 2 is not present or not configured! Address 3 is not present or not configured! Address 4 is an I/O Port : 1880h..189Fh System IRQ 11, INT# B Bus 0 (PCI), Device Number 31, Device Function 5 Vendor 8086h Intel Corporation Device 2485h 82801CA AC'97 Audio Controller (ICH3-S B1 step) Command 0001h (I/O Access) Status 0280h (Supports Back-To-Back Trans., Medium Timing) Revision 02h, Header Type 00h, Bus Latency Timer 00h Self test 00h (Self test not supported) PCI Class Multimedia, type Audio Subsystem ID 02221014h 82801CA/CAM (ICH3-S/ICH3-M) AC'97 Audio Controller (Guess Only!) Subsystem Vendor 1014h IBM Address 0 is an I/O Port : 1C00h..1CFFh Address 1 is an I/O Port : 18C0h..18FFh System IRQ 11, INT# B Bus 0 (PCI), Device Number 31, Device Function 6 Vendor 8086h Intel Corporation Device 2486h 82801CA AC'97 Modem Controller (ICH3-S B1 step) Command 0000h (Bus Access Disabled!!) Status 0280h (Supports Back-To-Back Trans., Medium Timing) Revision 02h, Header Type 00h, Bus Latency Timer 00h Self test 00h (Self test not supported) PCI Class Simple Communication, type Hayes Compatible Modem Subsystem ID 02271014h MiniPCI 802.11b+Modem Combo Card Subsystem Vendor 1014h IBM Address 0 is an I/O Port : 2400h..24FFh Address 1 is an I/O Port : 2000h..207Fh System IRQ 11, INT# B Bus 1 (AGP), Device Number 0, Device Function 0 Vendor 5333h S3 Inc Device 8C2Eh 86C584 SuperSavage/IXC SDRAM Command 0007h (I/O Access, Memory Access, BusMaster) Status 0230h (Has Capabilities List, Supports 66MHz, Medium Timing) Revision 05h, Header Type 00h, Bus Latency Timer 40h Minimum Bus Grant 04h, Maximum Bus Latency FFh Self test 00h (Self test not supported) Cache line size 32 Bytes (8 DWords) PCI Class Display, type VGA Subsystem ID 01FC1014h 86C584 SuperSavage/IXC IBM Subsystem Vendor 1014h IBM Address 0 is a Memory Address (0-4GiB) : C0100000h..C017FFFFh Address 1 is a Memory Address (0-4GiB, Prefetchable) : E8000000h..EBFFFFFFh Address 2 is a Memory Address (0-4GiB, Prefetchable) : E4000000h..E7FFFFFFh Address 3 is a Memory Address (0-4GiB, Prefetchable) : E0000000h..E1FFFFFFh System IRQ 11, INT# A Expansion ROM of 64 KiB decoded by this card, currently disabled New Capabilities List Present: Power Management Capability, Version 1.1 Supports low power State D1 Supports low power State D2 Does not support PME# signalling Current Power State : D0 (Device operational, no power saving) AGP Capability, Version 2.0 (AGP 4x and below support) AGP Speed(s) Supported : 1x 2x 4x FW Transfers Supported : No 4GiB Address Space Supported : No Sideband Addressing Supported : No Maximum Command Queue Length : 32 bytes AGP Speed Selected : 4x FW Transfers Enabled : No 4GiB Address Space Enabled : No AGP Enabled : Yes Sideband Addressing Enabled : No Current Command Queue Length : 1 byte Bus 2 (PCI), Device Number 0, Device Function 0 Vendor 104Ch Texas Instruments (TI) Device AC51h PCI1420 PC Card CardBus Controller Command 0107h (I/O Access, Memory Access, BusMaster, System Errors) Status 0210h (Has Capabilities List, Medium Timing) Revision 00h, Header Type 82h, Bus Latency Timer 40h Self test 00h (Self test not supported) Cache line size 32 Bytes (8 DWords) PCI Class Bridge, type PCI to Cardbus Subsystem ID 023B1014h Unknown Subsystem Vendor 1014h IBM System IRQ 11, INT# A CardBus Bridge Information: PCI Bus Number 2, CardBus Bus Number 3, Subordinate Bus number 5 CardBus Latency B0h Secondary Bus Command 03C0h (bus is in RESET, ints routed by ExCA) Secondary Bus Status 0200h (Medium Timing) Socket/ExCa Base Memory Address : 50000000h..50000FFFh Memory Range 0 : None Memory Range 1 : None I/O Port Range 0 : None I/O Port Range 1 : None New Capabilities List Present: Power Management Capability, Version 1.0 Supports low power State D1 Supports low power State D2 Supports PME# signalling from mode(s) D0, D1, D2, D3hot, D3cold PME# signalling is currently disabled 3.3v AUX Current required : 0 mA (Self powered) Current Power State : D0 (Device operational, no power saving) Bus 2 (PCI), Device Number 0, Device Function 1 Vendor 104Ch Texas Instruments (TI) Device AC51h PCI1420 PC Card CardBus Controller Command 0107h (I/O Access, Memory Access, BusMaster, System Errors) Status 0210h (Has Capabilities List, Medium Timing) Revision 00h, Header Type 82h, Bus Latency Timer 40h Self test 00h (Self test not supported) Cache line size 32 Bytes (8 DWords) PCI Class Bridge, type PCI to Cardbus Subsystem ID 023B1014h Unknown Subsystem Vendor 1014h IBM System IRQ 11, INT# B CardBus Bridge Information: PCI Bus Number 2, CardBus Bus Number 6, Subordinate Bus number 8 CardBus Latency B0h Secondary Bus Command 03C0h (bus is in RESET, ints routed by ExCA) Secondary Bus Status 0200h (Medium Timing) Socket/ExCa Base Memory Address : 51000000h..51000FFFh Memory Range 0 : None Memory Range 1 : None I/O Port Range 0 : None I/O Port Range 1 : None New Capabilities List Present: Power Management Capability, Version 1.0 Supports low power State D1 Supports low power State D2 Supports PME# signalling from mode(s) D0, D1, D2, D3hot, D3cold PME# signalling is currently disabled 3.3v AUX Current required : 0 mA (Self powered) Current Power State : D0 (Device operational, no power saving) Bus 2 (PCI), Device Number 2, Device Function 0 Vendor 1260h Intersil Americas Inc (Was: Harris Semiconductor) Device 3873h PRISM 2.5 802.11b 11Mbps Wireless Controller Command 0117h (I/O Access, Memory Access, BusMaster, MemWrite+Invalidate, System Errors) Status 0290h (Has Capabilities List, Supports Back-To-Back Trans., Medium Timing) Revision 01h, Header Type 00h, Bus Latency Timer 40h Self test 00h (Self test not supported) Cache line size 32 Bytes (8 DWords) PCI Class Network, type Other Subsystem ID 04061668h MiniPCI 802.11b+Modem Combo Card Subsystem Vendor 1668h Action Tec Electronics Inc Address 0 is a Memory Address (0-4GiB, Prefetchable) : EC000000h..EC000FFFh System IRQ 11, INT# A New Capabilities List Present: Power Management Capability, Version 1.1 Does not support low power State D1 or D2 Supports PME# signalling from mode(s) D0, D3hot PME# signalling is currently disabled 3.3v AUX Current required : 0 mA (Self powered) Current Power State : D0 (Device operational, no power saving) Bus 2 (PCI), Device Number 8, Device Function 0 Vendor 8086h Intel Corporation Device 1031h 82801CAM (ICH3) PRO/100 VE (LOM) Network Connection Command 0117h (I/O Access, Memory Access, BusMaster, MemWrite+Invalidate, System Errors) Status 0290h (Has Capabilities List, Supports Back-To-Back Trans., Medium Timing) Revision 42h, Header Type 00h, Bus Latency Timer 42h Minimum Bus Grant 08h, Maximum Bus Latency 38h Self test 00h (Self test not supported) Cache line size 32 Bytes (8 DWords) PCI Class Network, type Ethernet Subsystem ID 02091014h PRO/100 VE Network Connection Subsystem Vendor 1014h IBM Address 0 is a Memory Address (0-4GiB) : C0200000h..C0200FFFh Address 1 is an I/O Port : 7000h..703Fh System IRQ 11, INT# A New Capabilities List Present: Power Management Capability, Version 1.1 Supports low power State D1 Supports low power State D2 Supports PME# signalling from mode(s) D0, D1, D2, D3hot, D3cold PME# signalling is currently disabled 3.3v AUX Current required : 0 mA (Self powered) Current Power State : D0 (Device operational, no power saving) 580 mW D0 power consume 580 mW D0 power dissipate 400 mW D1 power consume 400 mW D1 power dissipate 400 mW D2 power consume 400 mW D2 power dissipate 400 mW D3 power consume 400 mW D3 power dissipate 0 mW common logic power consume ROM PCI IRQ routing table Tests.... ROM IRQ routing table found at F000h:DEB0h Table Version 1.0 - OK Table size 256 bytes - OK Table Checksum 91h - OK PCI Interrupt Router: 82801CAM (ICH3-M) LPC Interface IRQ's dedicated to PCI : None The ROM PCI IRQ routing table appears to be OK. IRQ Summary: IRQs 11,14,15 are used by PCI devices Shared IRQs: IRQ 11 is shared by 11 PCI Devices Thank you for your help!! Have a great day! Stu

Prenumerera: Sändning, Uppsamling, Index.
Stoppa prenumeration
Meddelande till ListMaster