On 2025-04-13, at 16:29:37, Neil Waldhauer wrote:
>
>On 04/13/25 01:43 pm, Massimo S. wrote:
>>
>>
>>Il 13/04/2025 18:01, Neil Waldhauer ha scritto:
>>>On 04/12/25 03:29 pm, Doug Bissett wrote:
>>>>On 2025-04-12, at 12:00:55, Allen Heath wrote:
>>>>>I've been happily running as a guest under VirtualBox 6.1.40 since 2022.
>>>>>However, it always reminds me that 7.1.6 is available, but I've been
>>>>>reluctant to rock a well working boat.  What's the advantage or
>>>>>disadvantage of either version under Windoze 11 host?
>>>>>
>>>>>The only "problems" I've had since 2022 are:
>>>>>* shared folders sometimes show shared host file timestamps in the Guest as
>>>>>GMT times for a while, then magically start displaying in the local
>>>>>timezone. And when that happens, if I create a file on the shared folder
>>>>>with the guest it appears at GMT time in the guest but the host displays it
>>>>>correctly in local time.  But restarting VirtualBox or just waiting a while
>>>>>the issue cures itself.
>>>>>* pretty good luck with the PCNet-Fast III adapter except that Net Used
>>>>>drives (or even a massive FTP) run out of resources after a lot of copying
>>>>>and then resume working again if I pause for about 10 minutes and then
>>>>>retry the operation.
>>>>>
>>>>>Will an upgrade fix any of this or just cause new problems?
>>>>>
>>>>>Thanks,
>>>>>Al
>>>>
>>>[snip]
>>>
>>>I'm trying to install eCS 2.1 on VirtualBox 7.1.6. I have not found a configuration that can finish the
>install. My best effort so far got to a place where printer installation was going on, but then the eCS installer
>said "Error zip file read error". At the same time, VirtualBox reports a crash and can't go on.
>>>
>>>I've used this iso a lot. I don't think it's defective. The installer seems to run.
>>>
>>>What system chipset do you recommend? Network card?
>>>
>>>I have also tried my eCS 2.2 b2, but that also crashes during the installation (TRAP in DaniS506)
>>
>>hi,
>>
>>don't use danis driver on VMs they do not work
>>
>>massimo
>Thank you! I now have a VM where eCS installation completed. The network does not function. What eCS
>driver would you recommend with the Intel PRO/1000 MT adapter?

I am using MMLEM.

--
****************************
From Doug Bissett's ArcaOS system
dougb007 AT ocii.com
****************************
... To many IDs, and passwords, Too few brain cells.

=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=
This message is sent to you because you are subscribed to
  the mailing list <virtualized_ecs_users@2rosenthals.com>.
To unsubscribe, E-mail to: <virtualized_ecs_users-off@2rosenthals.com>
To switch to the DIGEST mode, E-mail to <virtualized_ecs_users-digest@2rosenthals.com>
To switch to the INDEX mode, E-mail to <virtualized_ecs_users-index@2rosenthals.com>
Send administrative queries to  <virtualized_ecs_users-request@2rosenthals.com>
To subscribe (new addresses), E-mail to: <virtualized_ecs_users-on@2rosenthals.com> and reply to the confirmation email.
Web archives are publicly available at: http://lists.2rosenthals.com

This list is hosted by Rosenthal & Rosenthal, LLC
P.O. Box 281, Deer Park, NY 11729-0281. Non-
electronic communications related to content
contained in these messages should be directed
to the above address. (CAN-SPAM Act of 2003)

=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=